ExamVerdict

All tests / FCC Element 1: Marine Radio Operator Permit exam / Equipment Operations

FCC Element 1: Marine Radio Operator Permit exam: Equipment Operations practice

40 practice questions on Equipment Operations for the FCC Element 1: Marine Radio Operator Permit exam. Each answer comes with an explanation and the official source.

Focuses on VHF marine channel usage, squelch/power controls, EPIRB activation, and routine ship-to-ship calling procedures.

or practice the whole test

Sample questions

What is the purpose of the INT-USA control settings on a VHF?
  1. To change all VTS frequencies to Duplex so all vessels can receive maneuvering orders.
  2. To change all VHF channels from Duplex to Simplex while in U.S. waters.
  3. To change certain International Duplex channel assignments to simplex in the U.S. for VTS and other purposes. (correct answer)
  4. To change to NOAA weather channels and receive weather broadcasts while in the U.S.

The INT-USA setting specifically modifies certain International Duplex channel assignments to simplex when operating in U.S. waters. Changing all VHF channels to simplex is incorrect because it affects more than just specific international assignments. Changing all VTS frequencies to Duplex is not the function of this setting, nor is it solely for maneuvering orders.

FCC Commercial Element 1 Question Pool, Approved June 25, 2009 (FCC public notice DA 09-1417), Subelement C, key topic 13, question 1-13C1
1-13C1: What is the purpose of the INT-USA control settings on a VHF? Official answer C: To change certain International Duplex channel assignments to simplex in the U.S. for VTS and other purposes.
VHF ship station transmitters must have the capability of reducing carrier power to:
  1. 1 watt. (correct answer)
  2. 10 watts.
  3. 25 watts.
  4. 50 watts.

The requirement for VHF ship station transmitters is to have the capability to reduce carrier power to 1 watt. This low power setting is necessary for specific operational needs, unlike the other options which are higher and not mandated for this capability.

FCC Commercial Element 1 Question Pool, Approved June 25, 2009 (FCC public notice DA 09-1417), Subelement C, key topic 13, question 1-13C2
1-13C2: VHF ship station transmitters must have the capability of reducing carrier power to: Official answer A: 1 watt.
The Dual Watch (DW) function is used to:
  1. Listen to Ch-70 at the same time while monitoring Ch-16.
  2. Sequentially monitor 4 different channels.
  3. Sequentially monitoring all VHF channels.
  4. Listen on any selected channel while periodically monitoring Ch-16. (correct answer)

The Dual Watch function allows you to listen to any chosen channel while Ch-16 is monitored periodically. The other options incorrectly describe continuous listening or sequential monitoring of multiple channels. This feature is designed for simultaneous primary listening and emergency channel monitoring.

FCC Commercial Element 1 Question Pool, Approved June 25, 2009 (FCC public notice DA 09-1417), Subelement C, key topic 13, question 1-13C3
1-13C3: The Dual Watch (DW) function is used to: Official answer D: Listen on any selected channel while periodically monitoring Ch-16.
Which of the following statements best describes the correct setting for manual adjustment of the squelch control?
  1. Adjust squelch control to the minimum level necessary to barely suppress any background noise. (correct answer)
  2. Always adjust squelch control to its maximum level.
  3. Always adjust squelch control to its minimum level.
  4. Adjust squelch control to approximately twice the minimum level necessary to barely suppress any background noise.

Setting the squelch to the minimum level needed to suppress background noise prevents the radio from cutting out during actual conversation. Setting it too high will cause the radio to cut out even when a weak signal is present. Adjusting it to the maximum level or always using the minimum level without regard for noise is incorrect practice.

FCC Commercial Element 1 Question Pool, Approved June 25, 2009 (FCC public notice DA 09-1417), Subelement C, key topic 13, question 1-13C4
1-13C4: Which of the following statements best describes the correct setting for manual adjustment of the squelch control? Official answer A: Adjust squelch control to the minimum level necessary to barely suppress any background noise.
The “Scan” function is used to:
  1. Monitor Ch-16 continuously and switching to either Ch-70 or Ch-13 every 5 seconds.
  2. Scan Ch-16 for Distress calls.
  3. Scan Ch-70 for Distress alerts.
  4. Sequentially scan all or selected channels. (correct answer)

The Scan function is designed to move through a series of channels in order. Monitoring a specific channel like Ch-16 or Ch-70 is not the primary purpose of scanning. The function allows users to check multiple channels without manually switching each one.

FCC Commercial Element 1 Question Pool, Approved June 25, 2009 (FCC public notice DA 09-1417), Subelement C, key topic 13, question 1-13C5
1-13C5: The “Scan” function is used to: Official answer D: Sequentially scan all or selected channels.

Other topics on this test

Sources

FCC Commercial Element 1 Question Pool
Approved June 25, 2009 (FCC public notice DA 09-1417)
47 CFR Part 80, Stations in the Maritime Services (eCFR)
Current text, retrieved November 16, 2026

Check the current pool on fcc.gov and with your COLEM before your exam. ExamVerdict is not affiliated with Federal Communications Commission (FCC), given by COLEMs. Check the official material before test day.