All tests / FAA aviation mechanic Airframe knowledge test / Ice protection, cabin environment and fire protection
FAA aviation mechanic Airframe knowledge test: Ice protection, cabin environment and fire protection practice
136 practice questions on Ice protection, cabin environment and fire protection for the FAA aviation mechanic Airframe knowledge test. Each answer comes with an explanation and the official source.
Covers cabin pressurization outflow valves, air-cycle cooling, deice boots, thermal anti-ice, oxygen servicing, and fuselage fire detection.
Sample questions
What are the sources of heated air for thermal pneumatic anti-icing systems?
- engine exhaust heat exchangers and ram air only
- hot air from the compressor and ram air only
- hot bleed air from the turbine compressor, engine exhaust heat exchangers, and ram air heated by a combustion heater (correct answer)
- ram air only from the wing leading edge scoops
There are several sources of heated air, including hot bleed air from the turbine compressor, engine exhaust heat exchangers, and ram air heated by a combustion heater. These thermal pneumatic anti-icing systems are used for wings, leading edge slats, horizontal and vertical stabilizers, engine inlets, and more.
There are several sources of heated air, including hot bleed air from the turbine compressor, engine exhaust heat exchangers, and ram air heated by a combustion heater.
Which components have anti-icing systems installed on their leading edges?
- engine cowl leading edges (correct answer)
- flight deck windows
- propeller spinner
- air data probes
The ice and rain protection systems used on aircraft keep ice from forming on the engine cowl leading edges. This is listed among the components protected.
The ice and rain protection systems used on aircraft keep ice from forming on the following airplane components: • Wing leading edges. • Horizontal and vertical stabilizer leading edges. • Engine cowl leading edges.
How does rime ice affect the aerodynamic efficiency of airfoils?
- It increases lift and decreases drag
- It has no significant effect on aerodynamic efficiency
- It decreases the effectiveness of the aerodynamic efficiency of airfoils, reducing lift and increasing drag (correct answer)
- It causes the airfoil to become perfectly smooth
Rime ice is lighter in weight than clear ice and its weight is of little significance. However, its irregular shape and rough surface decrease the effectiveness of the aerodynamic efficiency of airfoils, reducing lift and increasing drag.
Rime ice forms when water drops are small, such as those in stratified clouds or light drizzle. The liquid portion remaining after initial impact freezes rapidly before the drop has time to spread over the aircraft surface. The small frozen droplets trap air giving the ice a white appearance.
What is one basic hazard created by ice or frost forming on aircraft?
- It causes immediate engine failure
- It could decrease the amount of lift (correct answer)
- It prevents all control surface movement
- It always leads to structural damage
Ice or frost forming on aircraft creates two basic hazards: 1. The resulting malformation of the airfoil that could decrease the amount of lift. 2. The additional weight and unequal formation of the ice that could cause unbalancing of the aircraft, making it hard to control.
Ice or frost forming on aircraft creates two basic hazards: 1. The resulting malformation of the airfoil that could decrease the amount of lift. 2. The additional weight and unequal formation of the ice that could cause unbalancing of the aircraft, making it hard to control.
If the temperature in the wing leading edge exceeds approximately +212 °F (outboard) or +350 °F (inboard), what illuminates on the annunciator panel?
- A blue ACIPS status indicator
- A red WING OV HT warning light (correct answer)
- A yellow WAI system warning light
- A green WAI operation light
If the temperature in the wing leading edge exceeds approximately +212 °F (outboard) or +350 °F (inboard), the red WING OV HT warning light on the annunciator panel illuminates.
If the temperature in the wing leading edge exceeds approximately +212 °F (outboard) or +350 °F (inboard), the red WING OV HT warning light on the annunciator panel illuminates.
Other topics on this test
-
Aircraft structures, aerodynamics and rigging158 questionsPractice
-
Sheet metal, welding, wood and fabric112 questionsPractice
-
Composites, plastics and aircraft finishing117 questionsPractice
-
Electrical, instruments and communication systems126 questionsPractice
-
Hydraulics, landing gear and fuel systems138 questionsPractice
Sources
FAA-H-8083-31B, 2023
Questions are written from FAA-H-8083-31B. Verify the current Aviation Mechanic Airframe ACS before testing. ExamVerdict is not affiliated with Federal Aviation Administration (FAA). Check the official material before test day.