ExamVerdict

All tests / FAA aviation mechanic Powerplant knowledge test / Fuel metering, induction and exhaust

FAA aviation mechanic Powerplant knowledge test: Fuel metering, induction and exhaust practice

115 practice questions on Fuel metering, induction and exhaust for the FAA aviation mechanic Powerplant knowledge test. Each answer comes with an explanation and the official source.

Covers float and pressure carburetors, continuous-flow fuel injection, FADEC controls, superchargers, turbochargers, and exhaust heat exchangers.

or practice the whole test

Sample questions

What is the most common fuel for turbine engines?
  1. 100LL
  2. Jet A (correct answer)
  3. AVGAS
  4. 80 (red)

Jet A is a kerosene-based fuel. The most common fuels are AVGAS for reciprocating engines and Jet A for turbine engines.

FAA, Aviation Maintenance Technician Handbook–Powerplant (FAA-H-8083-32B), FAA-H-8083-32B, 2023, Chapters 2 and 3: Fuel, induction and exhaust, part 1
The most common fuels are AVGAS for reciprocating engines and Jet A for turbine engines.
What does the LL stand for in 100LL AVGAS?
  1. Low Lead (correct answer)
  2. Liquid Limit
  3. Low Level
  4. Low Load

The LL stands for low lead. 100LL is a type of AVGAS.

FAA, Aviation Maintenance Technician Handbook–Powerplant (FAA-H-8083-32B), FAA-H-8083-32B, 2023, Chapters 2 and 3: Fuel, induction and exhaust, part 1
AVGAS is generally either 80 (red) or 100LL (blue) octane. The LL stands for low lead although it contains four times the lead of 80 octane AVGAS.
What can vapor lock result in when it interrupts fuel flow?
  1. Higher fuel pressure
  2. Partial or complete interruption of the fuel flow (correct answer)
  3. Increased fuel temperature
  4. Lowering of fuel boiling point

The resulting partial or complete interruption of the fuel flow is called vapor lock. Vapor pockets restrict fuel flow through units designed for liquids.

FAA, Aviation Maintenance Technician Handbook–Powerplant (FAA-H-8083-32B), FAA-H-8083-32B, 2023, Chapters 2 and 3: Fuel, induction and exhaust, part 1
The vapor pockets formed by this premature vaporization restrict the fuel flow through units which are designed to handle liquids rather than gases. The resulting partial or complete interruption of the fuel flow is called vapor lock.
What is the primary function of the boost pump in the fuel system?
  1. To control the airflow to the engine
  2. To remove water and dirt from the fuel
  3. To keep the fuel in the lines to the engine-driven pump under pressure (correct answer)
  4. To mix air with the fuel

The major improvement in reducing vapor lock is the incorporation of booster pumps in the fuel system. These booster pumps keep the fuel in the lines to the engine-driven pump under pressure. The pressure on the fuel reduces vapor formation and aids in moving a vapor pocket along.

FAA, Aviation Maintenance Technician Handbook–Powerplant (FAA-H-8083-32B), FAA-H-8083-32B, 2023, Chapters 2 and 3: Fuel, induction and exhaust, part 2
The major improvement in reducing vapor lock, however, is the incorporation of booster pumps in the fuel system. These booster pumps, which are used widely in most modern aircraft, keep the fuel in the lines to the engine-driven pump under pressure. The pressure on the fuel reduces vapor formation and aids in moving a vapor pocket along.
Where is the filtering unit located in the basic fuel system?
  1. At the metering device
  2. At the selector valve
  3. In the lowest part of the system (correct answer)
  4. In the fuel tank

The boost pump forces fuel through the selector valve to the main line strainer. This filtering unit, located in the lowest part of the system, removes water and dirt from the fuel.

FAA, Aviation Maintenance Technician Handbook–Powerplant (FAA-H-8083-32B), FAA-H-8083-32B, 2023, Chapters 2 and 3: Fuel, induction and exhaust, part 2
The boost pump forces fuel through the selector valve to the main line strainer. This filtering unit, located in the lowest part of the system, removes water and dirt from the fuel.

Other topics on this test

Sources

Questions are written from FAA-H-8083-32B. Check the current Aviation Mechanic Powerplant ACS before testing. ExamVerdict is not affiliated with Federal Aviation Administration (FAA). Check the official material before test day.