ExamVerdict

All tests / Ham radio Technician license exam / Amateur Radio Practices

Ham radio Technician license exam: Amateur Radio Practices practice

22 practice questions on Amateur Radio Practices for the Ham radio Technician license exam. Each answer comes with an explanation and the official source.

Focuses on station setup, SWR measurement, troubleshooting interference, grounding, and practical test equipment use on the workbench.

or practice the whole test

Sample questions

Which of the following is an appropriate power supply rating for a typical 50-watt output mobile FM transceiver?
  1. 24.0 volts at 4 amperes
  2. 13.8 volts at 4 amperes
  3. 24.0 volts at 12 amperes
  4. 13.8 volts at 12 amperes (correct answer)

The required power is 50 watts, and 13.8 volts at 12 amperes provides 165.6 watts, which is sufficient. The other options provide insufficient power or an unnecessarily high voltage for a typical mobile application.

NCVEC Technician Class Question Pool 2026-2030, Public release with errata of February 19, 2026, released into the public domain, Subelement T4, group T4A, question T4A01
T4A01 (D): Which of the following is an appropriate power supply rating for a typical 50-watt output mobile FM transceiver? Official answer D: 13.8 volts at 12 amperes
Which of the following should be considered when selecting an accessory SWR meter?
  1. The frequency and power level at which the measurements will be made (correct answer)
  2. The distance that the meter will be located from the antenna
  3. The maximum SWR anticipated on the transmission line
  4. The ability of the meter to compensate for a poor transmission line match to the antenna

The meter must be selected based on the specific frequency and power levels of the intended operation for accurate readings. The maximum SWR anticipated is important, but the operating frequency and power are primary selection criteria. The distance from the antenna and the ability to compensate for poor matches are not the primary factors for initial meter selection.

NCVEC Technician Class Question Pool 2026-2030, Public release with errata of February 19, 2026, released into the public domain, Subelement T4, group T4A, question T4A02
T4A02 (A): Which of the following should be considered when selecting an accessory SWR meter? Official answer A: The frequency and power level at which the measurements will be made
Why are short, heavy-gauge wires used for a transceiver’s DC power connection?
  1. To minimize voltage drop when transmitting (correct answer)
  2. To provide a close match to the power supply output impedance
  3. To avoid RF interference
  4. To minimize radiative losses in the power cable

Short, heavy-gauge wires reduce resistance, which directly minimizes voltage drop during power transmission. The other options do not accurately describe the primary function of wire gauge in DC power delivery. Minimizing voltage drop ensures the transceiver receives the necessary operating voltage for reliable transmission.

NCVEC Technician Class Question Pool 2026-2030, Public release with errata of February 19, 2026, released into the public domain, Subelement T4, group T4A, question T4A03
T4A03 (A): Why are short, heavy-gauge wires used for a transceiver’s DC power connection? Official answer A: To minimize voltage drop when transmitting
How are the audio input and output of a transceiver connected in a station configured to operate using FT8?
  1. To a computer running a terminal program and connected to a terminal node controller unit
  2. To the audio output and input of a computer running FT8 software (correct answer)
  3. To an FT8 conversion unit, a keyboard, and a computer monitor
  4. To a computer connected to the FT8converter.com website

The official answer is correct because FT8 requires the transceiver's audio to feed directly into and out of a computer running the specific FT8 software. The other choices describe incorrect or incomplete setups, such as using a terminal node controller or only connecting to a website without local software operation.

NCVEC Technician Class Question Pool 2026-2030, Public release with errata of February 19, 2026, released into the public domain, Subelement T4, group T4A, question T4A04
T4A04 (B): How are the audio input and output of a transceiver connected in a station configured to operate using FT8? Official answer B: To the audio output and input of a computer running FT8 software
Where should an RF power meter be installed?
  1. In the feed line, between the transmitter and antenna (correct answer)
  2. At the power supply output
  3. In parallel with the push-to-talk line and the antenna
  4. In the power supply cable, as close as possible to the radio

The RF power meter must measure the power actually radiated by the antenna. Measuring at the power supply output does not reflect the final transmitted power after the transmitter stage. Placing it in the feed line ensures the measurement is taken at the point of transmission to the antenna.

NCVEC Technician Class Question Pool 2026-2030, Public release with errata of February 19, 2026, released into the public domain, Subelement T4, group T4A, question T4A05
T4A05 (A): Where should an RF power meter be installed? Official answer A: In the feed line, between the transmitter and antenna

Other topics on this test

Sources

NCVEC Technician Class Question Pool 2026-2030
Public release with errata of February 19, 2026, released into the public domain

Exams are given by accredited Volunteer Examiner teams. Check the current pool and any errata on ncvec.org before your exam session. ExamVerdict is not affiliated with Federal Communications Commission (FCC), given by Volunteer Examiners. Check the official material before test day.