All tests / Ham radio Technician license exam / Signals and Emissions
Ham radio Technician license exam: Signals and Emissions practice
46 practice questions on Signals and Emissions for the Ham radio Technician license exam. Each answer comes with an explanation and the official source.
Covers AM, FM, single sideband, CW, and digital modes along with occupied bandwidth and basic modulation characteristics.
Sample questions
What type of modulation is commonly used for VHF packet radio transmissions?
- FM or PM (correct answer)
- SSB
- AM
- PSK
FM or PM is commonly used because it offers better noise immunity for radio communications. SSB is better for long-distance voice transmission, while AM is more susceptible to noise, and PSK is typically used for digital data rather than standard VHF packet radio.
T8A02 (A): What type of modulation is commonly used for VHF packet radio transmissions? Official answer A: FM or PM
Which type of voice mode is often used for long-distance (weak signal) contacts on the VHF and UHF bands?
- FM
- DRM
- SSB (correct answer)
- PM
SSB is effective for weak signals because it concentrates power into a narrow frequency band. FM requires more power to overcome noise on weak signals, while DRM and PM are not optimized for long-distance, low-signal contacts on these bands.
T8A03 (C): Which type of voice mode is often used for long-distance (weak signal) contacts on the VHF and UHF bands? Official answer C: SSB
Which type of modulation is commonly used for VHF and UHF voice repeaters?
- AM
- SSB
- PSK
- FM or PM (correct answer)
Frequency Modulation or Phase Modulation is standard for VHF and UHF voice repeaters because it offers good noise immunity. Amplitude Modulation is susceptible to noise, and Single Sideband and Phase Shift Keying are primarily used for data or narrowband communication, not wideband voice relaying.
T8A04 (D): Which type of modulation is commonly used for VHF and UHF voice repeaters? Official answer D: FM or PM
Which of the following signal types has the narrowest bandwidth?
- FM voice
- SSB voice
- CW (correct answer)
- Slow-scan TV
Continuous Wave has the narrowest bandwidth because it transmits a single, constant frequency without modulation. FM voice and SSB voice require bandwidth for frequency or sideband variations, and Slow-scan TV requires a much wider range of frequencies for its video signal.
T8A05 (C): Which of the following signal types has the narrowest bandwidth? Official answer C: CW
Which sideband is normally used for 10-meter HF, VHF, and UHF single-sideband communications?
- Upper sideband (correct answer)
- Lower sideband
- Suppressed sideband
- Inverted sideband
Upper sideband is the standard choice for single-sideband communications across 10-meter, VHF, and UHF bands. Lower sideband is not the typical configuration for these frequencies. Suppressed sideband and inverted sideband are not the standard modes used for these applications.
T8A06 (A): Which sideband is normally used for 10-meter HF, VHF, and UHF single-sideband communications? Official answer A: Upper sideband
Other topics on this test
-
Commission's Rules68 questionsPractice
-
Operating Procedures37 questionsPractice
-
Radio Wave Propagation35 questionsPractice
-
Amateur Radio Practices22 questionsPractice
-
Electrical Principles48 questionsPractice
-
Electronic and Electrical Components34 questionsPractice
-
Practical Circuits43 questionsPractice
-
Antennas and Feed Lines23 questionsPractice
-
Safety35 questionsPractice
Sources
Public release with errata of February 19, 2026, released into the public domain
Current text, retrieved November 16, 2026
Exams are given by accredited Volunteer Examiner teams. Check the current pool and any errata on ncvec.org before your exam session. ExamVerdict is not affiliated with Federal Communications Commission (FCC), given by Volunteer Examiners. Check the official material before test day.