ExamVerdict

All tests / OSHA construction safety practice test / Fall protection (Subpart M)

OSHA construction safety practice test: Fall protection (Subpart M) practice

30 practice questions on Fall protection (Subpart M) for the OSHA construction safety practice test. Each answer comes with an explanation and the official source.

Covers 29 CFR 1926 Subpart M fall arrest requirements, 6-foot trigger heights, guardrails, safety nets, leading-edge rules, and anchor strength limits.

or practice the whole test

Sample questions

What does body harness mean according to the definitions?
  1. A strap with means both for securing it about the waist and for attaching it to a lanyard, lifeline, or deceleration device
  2. Any device for holding the body belt or body harness closed around the employee's body
  3. Straps which may be secured about the employee in a manner that will distribute the fall arrest forces over at least the thighs, pelvis, waist, chest and shoulders with means for attaching it to other components of a personal fall arrest system (correct answer)
  4. A secure point of attachment for lifelines, lanyards or deceleration devices

Body harness means straps which may be secured about the employee in a manner that will distribute the fall arrest forces over at least the thighs, pelvis, waist, chest and shoulders with means for attaching it to other components of a personal fall arrest system.

29 CFR Part 1926, Safety and Health Regulations for Construction (eCFR), Current text, retrieved November 16, 2026, 29 CFR 1926 Subpart M: Fall Protection, part 1
Body harness means straps which may be secured about the employee in a manner that will distribute the fall arrest forces over at least the thighs, pelvis, waist, chest and shoulders with means for attaching it to other components of a personal fall arrest system.
What is prohibited for fall arrest as of January 1, 1998?
  1. using a body harness
  2. using a horizontal lifeline
  3. using a lifeline
  4. using a body belt (correct answer)

As of January 1, 1998, the use of a body belt for fall arrest is prohibited. This prohibition applies to the use of a body belt for fall arrest.

29 CFR Part 1926, Safety and Health Regulations for Construction (eCFR), Current text, retrieved November 16, 2026, 29 CFR 1926 Subpart M: Fall Protection, part 3
As of January 1, 1998, the use of a body belt for fall arrest is prohibited.
What defines an opening in a wall or partition through which employees can fall to a lower level?
  1. a gap or void 18 inches (48 cm) or more high and 30 inches (76 cm) or more wide
  2. a gap or void 30 inches (76 cm) or more high and 18 inches (48 cm) or more wide, in a wall or partition, through which employees can fall to a lower level (correct answer)
  3. any gap or void in a wall or partition that allows a fall to a lower level
  4. a gap or void 30 inches (76 cm) or more high and 18 inches (48 cm) or more wide

Opening means a gap or void 30 inches (76 cm) or more high and 18 inches (48 cm) or more wide, in a wall or partition, through which employees can fall to a lower level. This definition specifies both height and width requirements for an opening.

29 CFR Part 1926, Safety and Health Regulations for Construction (eCFR), Current text, retrieved November 16, 2026, 29 CFR 1926 Subpart M: Fall Protection, part 3
Opening means a gap or void 30 inches (76 cm) or more high and 18 inches (48 cm) or more wide, in a wall or partition, through which employees can fall to a lower level.
What is the requirement for a non-locking snaphook as part of personal fall arrest systems and positioning device systems as of January 1, 1998?
  1. it must be used with a body harness
  2. it must be used with a lifeline
  3. its use is prohibited (correct answer)
  4. it must be used with a deceleration device

As of January 1, 1998, the use of a non-locking snaphook as part of personal fall arrest systems and positioning device systems is prohibited. This prohibition applies to both personal fall arrest systems and positioning device systems.

29 CFR Part 1926, Safety and Health Regulations for Construction (eCFR), Current text, retrieved November 16, 2026, 29 CFR 1926 Subpart M: Fall Protection, part 3
As of January 1, 1998, the use of a non-locking snaphook as part of personal fall arrest systems and positioning device systems is prohibited.
What is the minimum height for a side or edge to be considered unprotected if there is no wall or guardrail system?
  1. 1.0 m
  2. 6 feet
  3. 1.8 m
  4. 39 inches (correct answer)

Unprotected sides and edges means any side or edge (except at entrances to points of access) of a walking/working surface, e.g., floor, roof, ramp, or runway where there is no wall or guardrail system at least 39 inches (1.0 m) high.

29 CFR Part 1926, Safety and Health Regulations for Construction (eCFR), Current text, retrieved November 16, 2026, 29 CFR 1926 Subpart M: Fall Protection, part 4
Unprotected sides and edges means any side or edge (except at entrances to points of access) of a walking/working surface, e.g., floor, roof, ramp, or runway where there is no wall or guardrail system at least 39 inches (1.0 m) high.

Other topics on this test

Sources

This is an independent OSHA construction safety practice test based on 29 CFR Part 1926, not an official OSHA Outreach certification. ExamVerdict is not affiliated with Occupational Safety and Health Administration (OSHA). Check the official material before test day.