ExamVerdict

All tests / OSHA construction safety practice test

OSHA construction safety practice test practice

Federal construction safety standards under 29 CFR Part 1926 govern fall protection, scaffolding, ladders, excavations, electrical work, personal protective equipment, and fire prevention on U.S. construction sites.

or pick a topic
Regulation
29 CFR Part 1926 (Construction)
Practice length
30 questions
Target score
70%
Key focus
Focus Four hazards & site standards
Authority
U.S. Department of Labor (OSHA)
Pass mark
70%
Run by
Occupational Safety and Health Administration (OSHA)
Practice questions here
265

This is an independent practice test for workers and supervisors studying federal OSHA construction safety rules—not an official OSHA Outreach 10-hour or 30-hour card exam. Every question is written directly from 29 CFR Part 1926 and shows the exact regulatory text beside the answer.

What this practice test is

This test checks your knowledge of the federal construction safety standards in 29 CFR Part 1926, the rules OSHA enforces on construction sites across the United States. It is built for workers, foremen, superintendents and safety coordinators who want to know the rules well, and for anyone preparing for a safety course or a company safety quiz.

It is not the OSHA Outreach 10-hour or 30-hour course test. Those cards come from authorized trainers who give their own course and test. What is tested there, and on a jobsite, comes from the same standards practised here.

The Focus Four

OSHA calls four hazards the "Focus Four", because they cause most construction deaths: falls, struck-by incidents, caught-in or caught-between incidents, and electrocution. A large share of the questions here sit on these four.

Falls. Under Subpart M, fall protection is generally required when you work 6 feet or more above a lower level, through guardrails, safety nets or personal fall arrest systems. Subpart L covers scaffolds, where the trigger height is 10 feet. Subpart X covers ladders and stairways, for example that a portable ladder used to reach an upper landing must extend at least 3 feet above it.

Struck-by. Vehicle and equipment rules, high-visibility clothing in traffic, and protection from falling objects with toe boards, screens and debris nets.

Caught-in or caught-between. Excavation rules in Subpart P. Trenches 5 feet deep or more need a protective system, such as sloping, shoring or a trench box, unless the excavation is entirely in stable rock. Excavations 20 feet deep or more need a system designed by a registered professional engineer. Spoil piles must be kept at least 2 feet back from the edge.

Electrocution. Subpart K covers ground-fault protection, assured equipment grounding programs, and keeping clear of overhead power lines.

What else is covered

The rest of Part 1926 shows up too: personal protective equipment (head, eye, face, hearing and respiratory protection), fire protection and prevention, cranes and derricks, concrete and masonry work, steel erection, stairways, tools, welding and cutting, and the general safety and health provisions that apply on every site.

How to use it

Every question here is written from the text of 29 CFR Part 1926, and each answer shows the passage it rests on. That makes it a direct check on what the rule actually says, which is not always what jobsite habit says.

Start with the fall protection topic. It is the most cited OSHA construction standard year after year, and its numbers (6 feet, 10 feet, 3 feet) appear in many questions. Then work through excavations, electrical and scaffolds. The practice runs are 30 questions, and a score of 70 percent or more is a good target before you move on to the less common subparts.

The rules here are federal. States with their own OSHA-approved plans, such as California, Washington and Oregon, can set stricter requirements, so check your state plan if you work there.

How this practice works

  1. Pick a mode

    Untimed mode is the default. Choose timed mode to match the real clock, or study mode to read answers without scoring.

  2. See the official source

    After every answer you see the explanation and the exact passage or key from Occupational Safety and Health Administration (OSHA).

  3. Review your misses

    Your browser remembers your best score and missed questions locally so you can drill weak topics or practise only your mistakes.

Practice by topic

Sample questions

What does body harness mean according to the definitions?
  1. A strap with means both for securing it about the waist and for attaching it to a lanyard, lifeline, or deceleration device
  2. Any device for holding the body belt or body harness closed around the employee's body
  3. Straps which may be secured about the employee in a manner that will distribute the fall arrest forces over at least the thighs, pelvis, waist, chest and shoulders with means for attaching it to other components of a personal fall arrest system (correct answer)
  4. A secure point of attachment for lifelines, lanyards or deceleration devices

Body harness means straps which may be secured about the employee in a manner that will distribute the fall arrest forces over at least the thighs, pelvis, waist, chest and shoulders with means for attaching it to other components of a personal fall arrest system.

29 CFR Part 1926, Safety and Health Regulations for Construction (eCFR), Current text, retrieved November 16, 2026, 29 CFR 1926 Subpart M: Fall Protection, part 1
Body harness means straps which may be secured about the employee in a manner that will distribute the fall arrest forces over at least the thighs, pelvis, waist, chest and shoulders with means for attaching it to other components of a personal fall arrest system.
What is prohibited for fall arrest as of January 1, 1998?
  1. using a body harness
  2. using a horizontal lifeline
  3. using a lifeline
  4. using a body belt (correct answer)

As of January 1, 1998, the use of a body belt for fall arrest is prohibited. This prohibition applies to the use of a body belt for fall arrest.

29 CFR Part 1926, Safety and Health Regulations for Construction (eCFR), Current text, retrieved November 16, 2026, 29 CFR 1926 Subpart M: Fall Protection, part 3
As of January 1, 1998, the use of a body belt for fall arrest is prohibited.
What defines an opening in a wall or partition through which employees can fall to a lower level?
  1. a gap or void 18 inches (48 cm) or more high and 30 inches (76 cm) or more wide
  2. a gap or void 30 inches (76 cm) or more high and 18 inches (48 cm) or more wide, in a wall or partition, through which employees can fall to a lower level (correct answer)
  3. any gap or void in a wall or partition that allows a fall to a lower level
  4. a gap or void 30 inches (76 cm) or more high and 18 inches (48 cm) or more wide

Opening means a gap or void 30 inches (76 cm) or more high and 18 inches (48 cm) or more wide, in a wall or partition, through which employees can fall to a lower level. This definition specifies both height and width requirements for an opening.

29 CFR Part 1926, Safety and Health Regulations for Construction (eCFR), Current text, retrieved November 16, 2026, 29 CFR 1926 Subpart M: Fall Protection, part 3
Opening means a gap or void 30 inches (76 cm) or more high and 18 inches (48 cm) or more wide, in a wall or partition, through which employees can fall to a lower level.
What is the requirement for a non-locking snaphook as part of personal fall arrest systems and positioning device systems as of January 1, 1998?
  1. it must be used with a body harness
  2. it must be used with a lifeline
  3. its use is prohibited (correct answer)
  4. it must be used with a deceleration device

As of January 1, 1998, the use of a non-locking snaphook as part of personal fall arrest systems and positioning device systems is prohibited. This prohibition applies to both personal fall arrest systems and positioning device systems.

29 CFR Part 1926, Safety and Health Regulations for Construction (eCFR), Current text, retrieved November 16, 2026, 29 CFR 1926 Subpart M: Fall Protection, part 3
As of January 1, 1998, the use of a non-locking snaphook as part of personal fall arrest systems and positioning device systems is prohibited.
What is the minimum height for a side or edge to be considered unprotected if there is no wall or guardrail system?
  1. 1.0 m
  2. 6 feet
  3. 1.8 m
  4. 39 inches (correct answer)

Unprotected sides and edges means any side or edge (except at entrances to points of access) of a walking/working surface, e.g., floor, roof, ramp, or runway where there is no wall or guardrail system at least 39 inches (1.0 m) high.

29 CFR Part 1926, Safety and Health Regulations for Construction (eCFR), Current text, retrieved November 16, 2026, 29 CFR 1926 Subpart M: Fall Protection, part 4
Unprotected sides and edges means any side or edge (except at entrances to points of access) of a walking/working surface, e.g., floor, roof, ramp, or runway where there is no wall or guardrail system at least 39 inches (1.0 m) high.

Related practice tests

Sources

This is an independent OSHA construction safety practice test based on 29 CFR Part 1926, not an official OSHA Outreach certification. ExamVerdict is not affiliated with Occupational Safety and Health Administration (OSHA). Check the official material before test day.