All tests / OSHA construction safety practice test / Scaffolds (Subpart L)
OSHA construction safety practice test: Scaffolds (Subpart L) practice
55 practice questions on Scaffolds (Subpart L) for the OSHA construction safety practice test. Each answer comes with an explanation and the official source.
Tests 29 CFR 1926 Subpart L scaffold load capacities, platform planking, guardrail heights, cross-bracing, and competent-person inspection duties.
Sample questions
What is the minimum load a scaffold and scaffold component must support without failure, except as provided in certain paragraphs?
- 3 times the maximum intended load
- 1 time the maximum intended load
- 2 times the maximum intended load
- 4 times the maximum intended load (correct answer)
Each scaffold and scaffold component shall be capable of supporting, without failure, its own weight and at least 4 times the maximum intended load applied or transmitted to it. This requirement applies except as provided in paragraphs (a)(2), (a)(3), (a)(4), (a)(5) and (g) of this section.
Except as provided in paragraphs (a)(2), (a)(3), (a)(4), (a)(5) and (g) of this section, each scaffold and scaffold component shall be capable of supporting, without failure, its own weight and at least 4 times the maximum intended load applied or transmitted to it.
What does 'equivalent' mean in the context of OSHA construction safety standards?
- A temporary solution until proper equipment is available
- Alternative designs, materials or methods to protect against a hazard which the employer can demonstrate will provide an equal or greater degree of safety for employees than the methods, materials or designs specified in the standard (correct answer)
- Any method that the employer prefers for convenience
- A substitute that provides less protection than the specified method
The standard defines equivalent as alternative designs, materials or methods to protect against a hazard which the employer can demonstrate will provide an equal or greater degree of safety for employees than the methods, materials or designs specified in the standard.
Equivalent means alternative designs, materials or methods to protect against a hazard which the employer can demonstrate will provide an equal or greater degree of safety for employees than the methods, materials or designs specified in the standard.
What is a 'competent person' according to OSHA construction standards?
- Any employee who has been designated by management to perform safety inspections
- A supervisor with at least five years of experience in construction
- One who is capable of identifying existing and predictable hazards in the surroundings or working conditions which are unsanitary, hazardous, or dangerous to employees, and who has authorization to take prompt corrective measures to eliminate them (correct answer)
- An employee who has completed a 40-hour safety course
The standard defines a competent person as one who is capable of identifying existing and predictable hazards in the surroundings or working conditions which are unsanitary, hazardous, or dangerous to employees, and who has authorization to take prompt corrective measures to eliminate them.
Competent person means one who is capable of identifying existing and predictable hazards in the surroundings or working conditions which are unsanitary, hazardous, or dangerous to employees, and who has authorization to take prompt corrective measures to eliminate them.
The maximum distance from the face for outrigger scaffolds shall be how many inches?
- 14 inches
- 18 inches
- 3 inches (correct answer)
- 12 inches
The maximum distance from the face for outrigger scaffolds shall be 3 inches (8 cm). This is provided under paragraph (b)(3) (i).
(i) The maximum distance from the face for outrigger scaffolds shall be 3 inches (8 cm);
Each end of a platform, unless cleated or otherwise restrained by hooks or equivalent means, shall extend over the centerline of its support at least how many inches?
- 6 inches (correct answer)
- 18 inches
- 12 inches
- 14 inches
Each end of a platform, unless cleated or otherwise restrained by hooks or equivalent means, shall extend over the centerline of its support at least 6 inches (15 cm). This is stated in paragraph (4).
(4) Each end of a platform, unless cleated or otherwise restrained by hooks or equivalent means, shall extend over the centerline of its support at least 6 inches (15 cm).
Other topics on this test
-
Fall protection (Subpart M)30 questionsPractice
-
Stairways and ladders (Subpart X)32 questionsPractice
-
Excavations and trenching (Subpart P)51 questionsPractice
-
Electrical safety (Subpart K)45 questionsPractice
-
General safety, PPE and fire protection52 questionsPractice
Sources
Current text, retrieved November 16, 2026
This is an independent OSHA construction safety practice test based on 29 CFR Part 1926, not an official OSHA Outreach certification. ExamVerdict is not affiliated with Occupational Safety and Health Administration (OSHA). Check the official material before test day.