ExamVerdict

All tests / FAA aviation mechanic General knowledge test / Fluid lines and fittings

FAA aviation mechanic General knowledge test: Fluid lines and fittings practice

48 practice questions on Fluid lines and fittings for the FAA aviation mechanic General knowledge test. Each answer comes with an explanation and the official source.

Focuses on aluminum/stainless tubing flaring, AN vs. AC fittings, flexible hose installation, and minimum bend radii.

or practice the whole test

Sample questions

What is used with corrosionresistant tubing?
  1. Cryofit fittings
  2. Code markings painted at the two ends
  3. Thicker wall aluminum alloy tubing
  4. Swaged or MS flareless fittings (correct answer)

Swaged or MS flareless fittings are used with corrosionresistant tubing. Each usually includes the manufacturer’s name or trademark, the Society of Automotive Engineers (SAE) number, and the physical condition of the metal.

FAA, Aviation Maintenance Technician Handbook–General (FAA-H-8083-30B), FAA-H-8083-30B, 2023, Chapter 9: Fluid lines and fittings, part 1
Swaged or MS flareless fittings are used with corrosionresistant tubing. Although identification markings for steel tubing differ, each usually includes the manufacturer’s name or trademark, the Society of Automotive Engineers (SAE) number, and the physical condition of the metal.
Under no circumstance is it permissible to use an automotive-type flaring tool that produces a flare of what angle?
  1. 45° (correct answer)
  2. 90°
  3. 35°
  4. 37°

Under no circumstance is it permissible to use an automotive-type flaring tool that produces a flare of 45°. The flaring tool used for aircraft tubing has male and female dies ground to produce a flare of 35° to 37°.

FAA, Aviation Maintenance Technician Handbook–General (FAA-H-8083-30B), FAA-H-8083-30B, 2023, Chapter 9: Fluid lines and fittings, part 5
Under no circumstance is it permissible to use an automotive-type flaring tool that produces a flare of 45°.
What is the maximum outside diameter tubing accommodated by the ordinary production tube bender?
  1. 11/2" (correct answer)
  2. 1"
  3. 3/4"
  4. 10"

The ordinary production tube bender accommodates tubing ranging from 1/4" to 11/2" outside diameter.

FAA, Aviation Maintenance Technician Handbook–General (FAA-H-8083-30B), FAA-H-8083-30B, 2023, Chapter 9: Fluid lines and fittings, part 4
The ordinary production tube bender accommodates tubing ranging from 1⁄4" to 11⁄2" outside diameter.
What is the temperature at which a fusible alloy melts when used in a modified filler method?
  1. 160 °F (correct answer)
  2. 175 °F
  3. 150 °F
  4. 180 °F

In a modified filler method, a fusible alloy melts at 160 °F.

FAA, Aviation Maintenance Technician Handbook–General (FAA-H-8083-30B), FAA-H-8083-30B, 2023, Chapter 9: Fluid lines and fittings, part 4
In this method, the tube is filled under hot water with a fusible alloy that melts at 160 °F.
What can be used with any soft metal tubing?
  1. Tube bending machines
  2. A hacksaw
  3. A tube cutter (correct answer)
  4. Special chipless cutters

Tubing may be cut with a tube cutter or a hacksaw. The cutter can be used with any soft metal tubing, such as copper, aluminum, or aluminum alloy.

FAA, Aviation Maintenance Technician Handbook–General (FAA-H-8083-30B), FAA-H-8083-30B, 2023, Chapter 9: Fluid lines and fittings, part 3
Tubing may be cut with a tube cutter or a hacksaw. The cutter can be used with any soft metal tubing, such as copper, aluminum, or aluminum alloy.

Other topics on this test

Sources

Questions are written from the FAA handbook. Check the current Aviation Mechanic General ACS and testing matrix before your test. ExamVerdict is not affiliated with Federal Aviation Administration (FAA). Check the official material before test day.