All tests / FAA aviation mechanic General knowledge test / Hand tools, measuring devices and electricity
FAA aviation mechanic General knowledge test: Hand tools, measuring devices and electricity practice
520 practice questions on Hand tools, measuring devices and electricity for the FAA aviation mechanic General knowledge test. Each answer comes with an explanation and the official source.
Tests micrometer/caliper readings, torque wrenches, Ohm's law, series-parallel circuits, batteries, and multimeters.
Sample questions
The voltage drop across the inductance (EXL) is:
- 12,100 volts
- 110 volts
- 67 volts
- 88 volts (correct answer)
The voltage drop across the inductance (EXL) is calculated as I × XL. The calculation shown results in 88 volts.
EXL = I × XL EXL = 11 × 8 = 88 volts
When the circuit contains resistance, inductance, and capacitance, the following equation is used to find the impedance:
- Z = R2 + XL + XC
- Z = (R2 + XC)2 - XL
- Z = R2 + (XL – XC)2 (correct answer)
- Z = (R2 + XL) + XC
When the circuit contains resistance, inductance, and capacitance, the following equation is used to find the impedance: Z = R2 + (XL – XC)2.
When the circuit contains resistance, inductance, and capacitance, the following equation is used to find the impedance: R2 + (XL – XC)2
The most common types of vacuum tubes fall into which families?
- (1) pentode, (2) tetrode, (3) triode, and (4) diode
- (1) diode, (2) triode, (3) tetrode, and (4) pentode (correct answer)
- (1) diode, (2) tetrode, (3) pentode, and (4) triode
- (1) triode, (2) tetrode, (3) pentode, and (4) diode
The most common types fall into the families: (1) diode, (2) triode, (3) tetrode, and (4) pentode.
While there are many types of vacuum tubes for a variety of applications, the most common types fall into one of the following families: (1) diode, (2) triode, (3) tetrode, and (4) pentode.
What is the primary difference between a basic AC generator and a basic DC generator?
- The AC generator uses brushes while the DC generator does not.
- The DC generator uses a commutator instead of slip rings. (correct answer)
- The DC generator uses a magnetic field while the AC generator does not.
- The DC generator uses a loop of wire while the AC generator uses a solid bar.
A basic DC generator is obtained by replacing the slip rings of a basic AC generator with two half cylinders called a commutator.
By replacing the slip rings of the basic AC generator with two half cylinders, called a commutator, a basic DC generator is obtained.
What happens to the induced emf when the loop of a generator is in position B?
- It is at a maximum rate. (correct answer)
- It is at a minimum rate.
- It is reversing polarity.
- It is at zero.
In position B, the flux is being cut at a maximum rate, which results in the induced emf being at a maximum.
In position B, the flux is now being cut at a maximum rate, which means that the induced emf is maximum.
Other topics on this test
-
Safety, ground operations and servicing95 questionsPractice
- Practice
-
Physics for aviation183 questionsPractice
-
Aircraft weight and balance98 questionsPractice
-
Aircraft materials, processes and hardware249 questionsPractice
-
Cleaning and corrosion121 questionsPractice
-
Fluid lines and fittings48 questionsPractice
-
Inspection concepts and techniques103 questionsPractice
-
Human factors82 questionsPractice
Sources
FAA-H-8083-30B, 2023
Questions are written from the FAA handbook. Check the current Aviation Mechanic General ACS and testing matrix before your test. ExamVerdict is not affiliated with Federal Aviation Administration (FAA). Check the official material before test day.