ExamVerdict

All tests / FAA aviation mechanic General knowledge test / Aircraft materials, processes and hardware

FAA aviation mechanic General knowledge test: Aircraft materials, processes and hardware practice

249 practice questions on Aircraft materials, processes and hardware for the FAA aviation mechanic General knowledge test. Each answer comes with an explanation and the official source.

Examines AN/MS/NAS bolts, safety wire, rivets, aluminum alloys, composites, and non-destructive heat treatment codes.

or practice the whole test

Sample questions

Alloys 122, A132, and 142 are commonly used in permanent mold castings for what principal uses?
  1. Structural beams
  2. Aircraft wing structures
  3. Internal combustion engines (correct answer)
  4. Automotive chassis

Alloys 122, A132, and 142 are commonly used in permanent mold castings in internal combustion engines. Permanent mold castings are used to obtain higher mechanical properties, better surfaces, or more accurate dimensions. Finer grain structure is produced in alloys subjected to the rapid cooling of metal molds.

FAA, Aviation Maintenance Technician Handbook–General (FAA-H-8083-30B), FAA-H-8083-30B, 2023, Chapter 7: Aircraft materials, processes and hardware, part 7
Alloys 122, A132, and 142 are commonly used in permanent mold castings, the principal uses of which are in internal combustion engines.
Magnesium alloy is used in die-castings when what is of primary importance?
  1. Corrosion resistance
  2. Ease of production
  3. Weight (correct answer)
  4. Strength

Die-castings used in aircraft are usually aluminum or magnesium alloy. If weight is of primary importance, magnesium alloy is used, because it is lighter than aluminum alloy. Aluminum alloy is frequently used because it is stronger than most magnesium alloys.

FAA, Aviation Maintenance Technician Handbook–General (FAA-H-8083-30B), FAA-H-8083-30B, 2023, Chapter 7: Aircraft materials, processes and hardware, part 7
Die-castings used in aircraft are usually aluminum or magnesium alloy. If weight is of primary importance, magnesium alloy is used, because it is lighter than aluminum alloy.
The 1xxx series of wrought aluminum alloys has what characteristic regarding its composition?
  1. Iron as the principal impurity
  2. Copper as the principal alloying element
  3. 99 percent aluminum or higher (correct answer)
  4. A four-digit index system

The 1000 series has 99 percent aluminum or higher. Iron and silicon are major impurities in the 1000 series. The 2000 series has copper as the principal alloying element. Wrought aluminum alloys are designated by a four-digit index system.

FAA, Aviation Maintenance Technician Handbook–General (FAA-H-8083-30B), FAA-H-8083-30B, 2023, Chapter 7: Aircraft materials, processes and hardware, part 7
1000 series: 99 percent aluminum or higher, excellent corrosion resistance, high thermal and electrical conductivity, low mechanical properties, excellent workability. Iron and silicon are major impurities.
For heat-treatable aluminum alloys, mechanical properties are obtained by what process?
  1. Heat-treating to a suitable temperature and quenching (correct answer)
  2. Cold-working after final annealing
  3. Using only the as fabricated condition
  4. Forcing molten metal under pressure

For heat-treatable aluminum alloys, the mechanical properties are obtained by heat-treating to a suitable temperature. This process involves holding at that temperature and then quenching. The metal is left in a supersaturated, unstable state and is then age hardened.

FAA, Aviation Maintenance Technician Handbook–General (FAA-H-8083-30B), FAA-H-8083-30B, 2023, Chapter 7: Aircraft materials, processes and hardware, part 7
For heat-treatable aluminum alloys, the mechanical properties are obtained by heat-treating to a suitable temperature, holding at that temperature long enough to allow the alloying constituent to enter into solid solution, and then quenching to hold the constituent in solution.
Type A-55 is an example of what titanium composition?
  1. commercially-pure titanium (correct answer)
  2. Type A-110AT
  3. C-110M
  4. alloyed titanium

Titanium is manufactured for commercial use in two basic compositions: commercially-pure titanium and alloyed titanium. A-55 is an example of commercially-pure titanium.

FAA, Aviation Maintenance Technician Handbook–General (FAA-H-8083-30B), FAA-H-8083-30B, 2023, Chapter 7: Aircraft materials, processes and hardware, part 12
Titanium is manufactured for commercial use in two basic compositions: commercially-pure titanium and alloyed titanium. A-55 is an example of commercially-pure titanium.

Other topics on this test

Sources

Questions are written from the FAA handbook. Check the current Aviation Mechanic General ACS and testing matrix before your test. ExamVerdict is not affiliated with Federal Aviation Administration (FAA). Check the official material before test day.