ExamVerdict

All tests / FCC Element 3: General Radiotelephone (GROL) exam / Antennas

FCC Element 3: General Radiotelephone (GROL) exam: Antennas practice

24 practice questions on Antennas for the FCC Element 3: General Radiotelephone (GROL) exam. Each answer comes with an explanation and the official source.

Covers dipole/whip antennas, parabolic dishes, gain, polarization, VSWR, and impedance matching.

or practice the whole test

Sample questions

Which of the following could cause a high standing wave ratio on a transmission line?
  1. Excessive modulation.
  2. An increase in output power.
  3. A detuned antenna coupler. (correct answer)
  4. Low power from the transmitter.

A detuned antenna coupler causes a mismatch between the transmission line and the antenna, leading to a high standing wave ratio. Increasing output power or low power from the transmitter does not inherently cause this issue. Excessive modulation is also not the primary cause of a high standing wave ratio.

FCC Commercial Element 3 Question Pool, Approved June 25, 2009 (FCC public notice DA 09-1417), Subelement J, key topic 63, question 3-63J1
3-63J1: Which of the following could cause a high standing wave ratio on a transmission line? Official answer C: A detuned antenna coupler.
Why is the value of the radiation resistance of an antenna important?
  1. Knowing the radiation resistance makes it possible to match impedances for maximum power transfer. (correct answer)
  2. Knowing the radiation resistance makes it possible to measure the near-field radiation density from transmitting antenna.
  3. The value of the radiation resistance represents the front-to-side ratio of the antenna.
  4. The value of the radiation resistance represents the front-to-back ratio of the antenna.

The radiation resistance is crucial because matching impedances ensures that maximum power is transferred from the source to the antenna. Knowing this value allows engineers to design matching networks effectively. The other choices describe different antenna characteristics, not the primary function of radiation resistance in power transfer.

FCC Commercial Element 3 Question Pool, Approved June 25, 2009 (FCC public notice DA 09-1417), Subelement J, key topic 63, question 3-63J2
3-63J2: Why is the value of the radiation resistance of an antenna important? Official answer A: Knowing the radiation resistance makes it possible to match impedances for maximum power transfer.
A radio frequency device that allows RF energy to pass through in one direction with very little loss but absorbs RF power in the opposite direction is a:
  1. Circulator.
  2. Wave trap.
  3. Multiplexer.
  4. Isolator. (correct answer)

An isolator is specifically designed to allow RF energy to pass in one direction with minimal loss while absorbing power in the reverse direction. A circulator directs energy sequentially to different ports, not just one-way transmission with absorption. A wave trap is used to absorb specific frequencies, and a multiplexer combines multiple signals onto one carrier.

FCC Commercial Element 3 Question Pool, Approved June 25, 2009 (FCC public notice DA 09-1417), Subelement J, key topic 63, question 3-63J3
3-63J3: A radio frequency device that allows RF energy to pass through in one direction with very little loss but absorbs RF power in the opposite direction is a: Official answer D: Isolator.
What is an advantage of using a trap antenna?
  1. It may be used for multiband operation. (correct answer)
  2. It has high directivity in the high-frequency bands.
  3. It has high gain.
  4. It minimizes harmonic radiation.

Trap antennas are designed to resonate at multiple frequencies, which allows for multiband operation. High gain and high directivity are characteristics of directional antennas, not necessarily trap antennas. Minimizing harmonic radiation is a design goal but not the primary advantage of using a trap antenna.

FCC Commercial Element 3 Question Pool, Approved June 25, 2009 (FCC public notice DA 09-1417), Subelement J, key topic 63, question 3-63J4
3-63J4: What is an advantage of using a trap antenna? Official answer A: It may be used for multiband operation.
What is meant by the term radiation resistance of an antenna?
  1. Losses in the antenna elements and feed line.
  2. The specific impedance of the antenna.
  3. The resistance in the trap coils to received signals.
  4. An equivalent resistance that would dissipate the same amount of power as that radiated from an antenna. (correct answer)

The official answer correctly defines radiation resistance as the equivalent resistance that dissipates the same power as the antenna radiates. Losses in the antenna elements and feed line are related to efficiency, not radiation resistance itself. The specific impedance and the resistance in the trap coils do not define this specific concept.

FCC Commercial Element 3 Question Pool, Approved June 25, 2009 (FCC public notice DA 09-1417), Subelement J, key topic 63, question 3-63J5
3-63J5: What is meant by the term radiation resistance of an antenna? Official answer D: An equivalent resistance that would dissipate the same amount of power as that radiated from an antenna.

Other topics on this test

Sources

FCC Commercial Element 3 Question Pool
Approved June 25, 2009 (FCC public notice DA 09-1417)

Check the current pool on fcc.gov and with your COLEM before your exam. ExamVerdict is not affiliated with Federal Communications Commission (FCC), given by COLEMs. Check the official material before test day.