ExamVerdict

All tests / FCC Element 3: General Radiotelephone (GROL) exam / Receivers

FCC Element 3: General Radiotelephone (GROL) exam: Receivers practice

46 practice questions on Receivers for the FCC Element 3: General Radiotelephone (GROL) exam. Each answer comes with an explanation and the official source.

Focuses on superheterodyne sensitivity, selectivity, image rejection, AGC, squelch, and IF filtering.

or practice the whole test

Sample questions

What is the limiting condition for sensitivity in a communications receiver?
  1. The noise floor of the receiver. (correct answer)
  2. The power supply output ripple.
  3. The two-tone intermodulation distortion.
  4. The input impedance to the detector.

The noise floor sets the lowest detectable signal level, which is the limiting factor for sensitivity. Power supply ripple, two-tone intermodulation distortion, and input impedance do not determine the fundamental limit of how weak a signal can be reliably detected.

FCC Commercial Element 3 Question Pool, Approved June 25, 2009 (FCC public notice DA 09-1417), Subelement F, key topic 41, question 3-41F1
3-41F1: What is the limiting condition for sensitivity in a communications receiver? Official answer A: The noise floor of the receiver.
What is the definition of the term “receiver desensitizing”?
  1. A burst of noise when the squelch is set too low.
  2. A reduction in receiver sensitivity because of a strong signal on a nearby frequency. (correct answer)
  3. A burst of noise when the squelch is set too high.
  4. A reduction in receiver sensitivity when the AF gain control is turned down.

Receiver desensitizing is specifically caused by a strong signal on a nearby frequency, which reduces the receiver's sensitivity. The other options describe squelch issues or gain control effects, not desensitization. A strong nearby signal is the defining characteristic of this phenomenon.

FCC Commercial Element 3 Question Pool, Approved June 25, 2009 (FCC public notice DA 09-1417), Subelement F, key topic 41, question 3-41F2
3-41F2: What is the definition of the term “receiver desensitizing”? Official answer B: A reduction in receiver sensitivity because of a strong signal on a nearby frequency.
What is the term used to refer to a reduction in receiver sensitivity caused by unwanted high-level adjacent channel signals?
  1. Desensitizing. (correct answer)
  2. Intermodulation distortion.
  3. Quieting.
  4. Overloading.

Desensitizing is the correct term for reduced receiver sensitivity due to strong adjacent channel signals. Intermodulation distortion, quieting, and overloading describe different signal or system behaviors that do not specifically refer to this type of sensitivity reduction.

FCC Commercial Element 3 Question Pool, Approved June 25, 2009 (FCC public notice DA 09-1417), Subelement F, key topic 41, question 3-41F3
3-41F3: What is the term used to refer to a reduction in receiver sensitivity caused by unwanted high-level adjacent channel signals? Official answer A: Desensitizing.
How can selectivity be achieved in the front-end circuitry of a communications receiver?
  1. By using an audio filter.
  2. By using an additional RF amplifier stage.
  3. By using an additional IF amplifier stage.
  4. By using a preselector. (correct answer)

A preselector is specifically designed to filter out unwanted signals before they reach the main receiver circuitry. Using an audio filter only affects low frequencies, and an additional RF or IF amplifier stage boosts signals without providing necessary frequency discrimination. Therefore, the preselector is the correct method for achieving selectivity in the front-end.

FCC Commercial Element 3 Question Pool, Approved June 25, 2009 (FCC public notice DA 09-1417), Subelement F, key topic 42, question 3-42F1
3-42F1: How can selectivity be achieved in the front-end circuitry of a communications receiver? Official answer D: By using a preselector.
How much gain should be used in the RF amplifier stage of a receiver?
  1. Sufficient gain to allow weak signals to overcome noise generated in the first mixer stage. (correct answer)
  2. As much gain as possible short of self oscillation.
  3. Sufficient gain to keep weak signals below the noise of the first mixer stage.
  4. It depends on the amplification factor of the first IF stage.

The correct gain ensures that the weak incoming signals are strong enough to be detected above the noise floor of the subsequent first mixer stage. Using as much gain as possible short of self oscillation risks instability, and keeping weak signals below the first mixer's noise level would result in signal loss. The gain requirement is dictated by the noise characteristics of the first mixer, not the first IF stage's amplification factor.

FCC Commercial Element 3 Question Pool, Approved June 25, 2009 (FCC public notice DA 09-1417), Subelement F, key topic 42, question 3-42F3
3-42F3: How much gain should be used in the RF amplifier stage of a receiver? Official answer A: Sufficient gain to allow weak signals to overcome noise generated in the first mixer stage.

Other topics on this test

Sources

FCC Commercial Element 3 Question Pool
Approved June 25, 2009 (FCC public notice DA 09-1417)

Check the current pool on fcc.gov and with your COLEM before your exam. ExamVerdict is not affiliated with Federal Communications Commission (FCC), given by COLEMs. Check the official material before test day.