All tests / FCC Element 3: General Radiotelephone (GROL) exam / Digital Logic
FCC Element 3: General Radiotelephone (GROL) exam: Digital Logic practice
42 practice questions on Digital Logic for the FCC Element 3: General Radiotelephone (GROL) exam. Each answer comes with an explanation and the official source.
Tests logic gates, flip-flops, binary/hex math, microprocessors, and ADC/DAC conversion stages.
Sample questions
What is the voltage range considered to be valid logic low input in a TTL device operating at 5 volts?
- 2.0 to 5.5 volts.
- -2.0 to -5.5 volts.
- Zero to 0.8 volts. (correct answer)
- 5.2 to 34.8 volts.
The official answer is correct because a logic low input in TTL devices is defined as a voltage between zero and 0.8 volts. The other choices describe voltage ranges that are either too high, negative, or encompass valid logic high levels, not logic low.
3-33E1: What is the voltage range considered to be valid logic low input in a TTL device operating at 5 volts? Official answer C: Zero to 0.8 volts.
What is the voltage range considered to be a valid logic high input in a TTL device operating at 5.0 volts?
- 2.0 to 5.5 volts. (correct answer)
- 1.5 to 3.0 volts.
- 1.0 to 1.5 volts.
- 5.2 to 34.8 volts.
The official answer is correct because a valid logic high input for a TTL device at 5.0 volts is defined within the 2.0 to 5.5 volt range. The other choices describe voltage ranges that are either too low to register as a high or are outside the specified operating limits for a logic high input.
3-33E2: What is the voltage range considered to be a valid logic high input in a TTL device operating at 5.0 volts? Official answer A: 2.0 to 5.5 volts.
What is the common power supply voltage for TTL series integrated circuits?
- 12 volts.
- 13.6 volts.
- 1 volt.
- 5 volts. (correct answer)
TTL series integrated circuits are designed to operate reliably with a 5 volts power supply. Twelve volts and thirteen point six volts are too high for standard TTL operation, and one volt is too low to provide sufficient operating voltage for these circuits.
3-33E3: What is the common power supply voltage for TTL series integrated circuits? Official answer D: 5 volts.
TTL inputs left open develop what logic state?
- A high-logic state. (correct answer)
- A low-logic state.
- Open inputs on a TTL device are ignored.
- Random high- and low-logic states.
TTL inputs left open develop a high-logic state because the internal circuitry pulls the voltage up when no signal is present. The other options are incorrect because open inputs are not ignored, do not result in a low-logic state, and do not produce random states.
3-33E4: TTL inputs left open develop what logic state? Official answer A: A high-logic state.
Which of the following instruments would be best for checking a TTL logic circuit?
- VOM.
- DMM.
- Continuity tester.
- Logic probe. (correct answer)
A logic probe is specifically designed to indicate the high or low state of digital signals in a TTL circuit. A VOM and DMM measure voltage but are not ideal for digital state checking, and a continuity tester only checks for a complete electrical path, not logic levels.
3-33E5: Which of the following instruments would be best for checking a TTL logic circuit? Official answer D: Logic probe.
Other topics on this test
-
Principles44 questionsPractice
-
Electrical Math48 questionsPractice
-
Components53 questionsPractice
-
Receivers46 questionsPractice
-
Transmitters34 questionsPractice
-
Antennas24 questionsPractice
-
Aircraft35 questionsPractice
-
Installation, Maintenance & Repair46 questionsPractice
-
Marine26 questionsPractice
-
Radar27 questionsPractice
-
Satellite24 questionsPractice
Sources
Approved June 25, 2009 (FCC public notice DA 09-1417)
Check the current pool on fcc.gov and with your COLEM before your exam. ExamVerdict is not affiliated with Federal Communications Commission (FCC), given by COLEMs. Check the official material before test day.