All tests / FCC Element 3: General Radiotelephone (GROL) exam / Radar
FCC Element 3: General Radiotelephone (GROL) exam: Radar practice
27 practice questions on Radar for the FCC Element 3: General Radiotelephone (GROL) exam. Each answer comes with an explanation and the official source.
Covers pulse width, PRF, magnetron transmitters, waveguides, TR switches, and range/bearing resolution.
Sample questions
What is the normal range of pulse repetition rates?
- 2,000 to 4,000 pps.
- 1,000 to 3,000 pps.
- 500 to 1,000 pps.
- 500 to 2,000 pps. (correct answer)
The normal range for pulse repetition rates is 500 to 2,000 pps. The other ranges are too high or too low for typical operational standards. Therefore, 500 to 2,000 pps is the correct standard range.
3-90O1: What is the normal range of pulse repetition rates? Official answer D: 500 to 2,000 pps.
The RADAR range in nautical miles to an object can be found by measuring the elapsed time during a RADAR pulse and dividing this quantity by:
- 0.87 seconds.
- 1.15 us.
- 12.346 us. (correct answer)
- 1.073 us.
The official answer is correct because the calculation requires dividing the elapsed time by the speed of light in a vacuum, which is approximately 12.346 microseconds per nautical mile for a two-way measurement. The other choices are incorrect because they do not represent the necessary conversion factor derived from the speed of light. Using any of the other values will result in an inaccurate range measurement.
3-90O2: The RADAR range in nautical miles to an object can be found by measuring the elapsed time during a RADAR pulse and dividing this quantity by: Official answer C: 12.346 us.
Shipboard RADAR is most commonly operated in what band?
- VHF.
- UHF.
- SHF. (correct answer)
- EHF.
SHF is the most common band for shipboard RADAR because it offers a good balance between resolution and antenna size. VHF is too low for effective radar range, while UHF, EHF, and SHF offer different performance trade-offs that make SHF the standard choice.
3-90O4: Shipboard RADAR is most commonly operated in what band? Official answer C: SHF.
The pulse repetition rate (prr) of a RADAR refers to the:
- Reciprocal of the duty cycle.
- Pulse rate of the local oscillator.
- Pulse rate of the klystron.
- Pulse rate of the magnetron. (correct answer)
The pulse repetition rate specifically measures how often the radar transmits a pulse, which is determined by the magnetron's firing rate. The other options describe related but distinct operational parameters, not the definition of PRR.
3-90O5: The pulse repetition rate (prr) of a RADAR refers to the: Official answer D: Pulse rate of the magnetron.
The ATR box:
- Prevents the received signal from entering the transmitter. (correct answer)
- Protects the receiver from strong RADAR signals.
- Turns off the receiver when the transmitter is on.
- All of the above.
The ATR box specifically functions to stop incoming signals from reaching the transmitter. The other options describe functions that are not the primary role of the ATR box. Turning off the receiver when the transmitter is on is a separate protection mechanism.
3-91O1: The ATR box: Official answer A: Prevents the received signal from entering the transmitter.
Other topics on this test
-
Principles44 questionsPractice
-
Electrical Math48 questionsPractice
-
Components53 questionsPractice
-
Digital Logic42 questionsPractice
-
Receivers46 questionsPractice
-
Transmitters34 questionsPractice
-
Antennas24 questionsPractice
-
Aircraft35 questionsPractice
-
Installation, Maintenance & Repair46 questionsPractice
-
Marine26 questionsPractice
-
Satellite24 questionsPractice
Sources
Approved June 25, 2009 (FCC public notice DA 09-1417)
Check the current pool on fcc.gov and with your COLEM before your exam. ExamVerdict is not affiliated with Federal Communications Commission (FCC), given by COLEMs. Check the official material before test day.